Skip to content
Kibi Connect
Manual Kibi Connect

Stamping Terminal (Kibi Terminal S)

Updated Reading time: 5 min

On this page

With the Kibi Terminal S, employees clock in and out using a chip or card: simply hold it up, done. The terminal is permanently mounted on the wall, for example at the entrance, and runs continuously on a power supply.

Coming and Going#

In standby mode, the terminal displays the time in large font and "Hold chip up". Hold your chip or card briefly to the card target. The terminal automatically switches between Coming and Going.

What you see and hear

Meaning

Green symbol ▶, your first name, COMING, ascending tone

Coming is recorded.

Yellow symbol ■, your first name, GOING 8:12 h, descending tone

Going is recorded, along with your working hours for today.

Balance +3:22 h

Your working time account (if enabled on the terminal).

Red cross, Chip not recognized, low double tone

The chip is not assigned to any person. Contact the HR department.

SAVED with time, "Network missing, will be submitted later"

The terminal currently has no network. Your stamp is saved with the time and will be submitted later.

Terminal off

The terminal is currently not enabled for stamping.

Please wait

Too many attempts in a short time. Try again after a few seconds.

Symbol and tone indicate the result even without reading.

Made a mistake? Immediately after stamping, "A: undo" appears for 5 seconds. Press the A button to the left of the display. The terminal shows "COMING UNDO" or "GOING UNDO", and you will receive a message about it in Kibi. If someone else holds their chip up in the meantime, undo is no longer possible. Later corrections can be made in Kibi under Time Tracking.

Button A: Select Mode#

If you press A before holding up the chip, you can select what should happen. Each press cycles through:

  • COMING: records Coming. If you are already on duty, the terminal shows "ON DUTY since 07:58" and does not record anything.

  • GOING: records Going. If you have already left, it shows "ALREADY LEFT at 16:31".

  • BALANCE: only shows your working time account without stamping.

Without a chip, the terminal returns to the normal process after 10 seconds.

Outside Working Hours#

Outside working hours, the display is off. Stamping still works: hold up the chip, and the display shows the result as usual. If you want to select something beforehand, press A once: the display turns on for 30 minutes, but the press itself does not select anything yet.

For HR: Assign Chip#

Each person is assigned their chip in the HR section: Open person → HR tab → Chip or Card field. There are three ways:

  1. Read chip at terminal: Select "Read chip at terminal", choose the terminal, and "Start reading". The terminal displays "Chip for HR" for 2 minutes. Hold the chip up, the number appears in the dialog. Save.

  2. Read with phone: Select "Read with phone". You will receive a message on your phone, tap it, and hold the chip to the phone (NFC must be enabled).

  3. From "Unknown Chips and Cards": If the person has already held their chip to the terminal ("Chip not recognized"), it appears in the HR tab under "Unknown Chips and Cards (last 30 days)". There, select "Assign to this person". The same list is available under Administration → Kibi Devices → Terminals.

This list also helps if someone says "The terminal doesn't recognize me": If the chip is listed there, it was detected but not assigned to anyone. If it is missing, the terminal did not read it (see "Which chips and cards work?").

Chip lost? Clear the Chip or Card field and assign a new chip. The old one will no longer work for stamping. A chip can only belong to one person at a time.

Stamps that the terminal saved without a network and submitted later are marked in the person's month as "submitted later (terminal offline)".

For Admins: Set Up Terminal#

  1. Wi-Fi: Connect the terminal via USB-C to a computer with the Kibi Desktop App and enter Wi-Fi and Kibi address there.

  2. Pairing: The terminal displays a code. In Kibi under Administration → Kibi Devices → "Pair Kibi Device", enter the code. If the terminal is on the same network, it often appears there automatically as a new device. It will be listed under the Terminals tab and is set up for time tracking. Give it a short name, for example "Entrance". The name appears at the top of the display.

  3. Mounting: Screw the wall plate vertically ("TOP" must be at the top), position the center of the card target at 105 cm above the floor (accessible, including for wheelchair users). Use the included USB-C cable with angled plug and the power supply. Plug in the cable, place the housing on and push it down until it clicks. A screw is not necessary; an optional security screw is available.

  4. Test: Hold an assigned chip up, "COMING" should appear. Delete the test stamp afterward in Time Tracking.

Removing: Use a small screwdriver to press into the slot at the bottom left and push the housing upward.

Restart: Briefly unplug the power supply and plug it back in.

Serial number ("SN: KD-…"): located on the back of the wall plate and in Kibi under the terminal in Kibi Devices.

Identify terminal: In Kibi, select "Identify terminal" for the terminal. The device will blink and beep briefly.

Settings per Terminal#

Under Kibi Devices → Terminals → Open terminal:

Switch

Default

Effect

Stamping with chip or card

on

Without this switch, the terminal shows "Terminal off".

Select mode via button A

on

Pre-select Coming, Going, or Balance.

Allow undo at terminal

on

5 seconds "A: undo" after each stamp.

Display balance at terminal

on

Shows working time account after stamping. Anyone standing next to the terminal can see it.

Turn off display outside working hours

on

The display is only on during working hours, i.e., within the core working hours of your working time models; without core hours, Monday to Friday 6 AM to 8 PM. Stamping always works. Saves the display and power.

Permissions#

Who can manage terminals is determined in role management: Manage Terminals (separate from Manage Displays and Manage Buddies). Anyone who can edit a person's HR data can assign chips.

Without Network#

If Wi-Fi fails, the terminal continues to stamp. It saves each stamp with the time and submits it once it is back online, for up to 72 hours. Only then does Kibi decide whether it was Coming or Going. Unknown chips are rejected in the same way. If storage is full, the terminal shows "STORAGE FULL" and does not stamp. Please still ensure stable Wi-Fi reception at the mounting location.

Which Chips and Cards Work?#

  • Suitable are chips and cards with 13.56 MHz (NFC), such as NTAG key fobs, MIFARE cards, or many employee IDs.

  • Not suitable are older 125 kHz chips (e.g., EM4100) and LEGIC IDs. The terminal does not respond to them at all.

  • Quick test: If a phone with NFC responds to the chip, the terminal can also read it.

Data Privacy and Co-Determination#

  • Co-determination: Electronic time tracking is subject to co-determination (§ 87 (1) No. 6 BetrVG). If there is a works or staff council, involve them before introduction.

  • What is stored: the chip number for the person, and the times when stamping, just like any time tracking in Kibi. The terminal only displays the first name. Without a network, the chip number and time remain on the device until submission and are then deleted.

  • Unknown chips and cards: Number, terminal, and time for a maximum of 30 days, visible only to authorized users, deleted upon assignment. This may also include the number of a foreign card accidentally held to the reader, such as a bank card.

  • Balance at terminal: If enabled, people nearby can briefly see it. If this is not desired, disable it at the terminal. Then it will no longer appear after each stamp, but can still be checked via Button A → BALANCE.

  • Security: The number of simple chips can be copied with some effort. This is common for time tracking. Do not use simple chips for doors and access control.

  • Stamping for others is not allowed.